Kelvin Redefined with the Help of Mahr Form Measurement System

PTB defines the unit kelvin with the help of the reference formtester MarForm MFU 110 WP

 

 MarForm MFU 110 WP Piston

PTB is using the White Point optical stylus system on the MarForm MFU 110 WP to calculate the geometry of the system's pistons and cylinders.

PROVIDENCE, RI, USA — In conjunction with the General Conference on Weights and Measures (CGPM), the kelvin, the basic unit of thermodynamic temperature, is currently being newly defined at the PTB (Physikalisch-Technischen Bundesanstalt) in Braunschweig, Germany, the counterpart of NIST in the USA.

The goal of PTB’s portion of the program is a precise determination of the Boltzmann constant, k, the conversion factor between thermal and mechanical energy. The project is being done with the help of a highly accurate reference formtester from Mahr, the MarForm MFU 110 WP, which includes both tactile and optical sensors, and provides accuracy into the nanometer range.

In October of 2011, the CGPM adopted a plan to redefine four of the seven base units of the International System of Units (SI) in terms of the invariants of nature â?? the fundamental physical constants or properties of atoms.

A previous example of this was the redefinition of the meter in 1983, which links it to an exact value of the speed of light in a vacuum. The Conference recommended that efforts be made by the various National Metrology Institutes to reduce the uncertainties of these constants.

The CGPM also noted that, “The kelvin is currently defined in terms of an intrinsic property of water that, while being an invariant of nature, in practice depends on the purity and isotopic composition of the water used.” Instead, the Conference suggested that it was  “possible to redefine the kelvin so that it is linked to an exact numerical value of the Boltzmann constant, k,” which links temperature to mechanical energy.

As part of their work to precisely determine the Boltzmann constant, PTB needed to define absolute helium pressures. These were realized with the help of a pressure balance, the essential components of which were piston-cylinder systems.

For the precise calculation of pressure, the geometry of the pistons and cylinders at ambient pressure had to be known exactly: hence, PTB’s use of the reference formtester from Mahr. This highly precise reference unit is the world’s leading instrument for tactile distance and diameter measurements in the measuring range of up to 180 mm.

PTB used the White Point optical stylus system on the MarForm MFU 110 WP to measure the pistons and cylinders. White Point is an optical (interferometrical) stylus system for form measuring machines which allows form and diameter measurements of precision mechanical parts with tolerances of less than 1.0 µm.

The optical system is based on a novel concept of short coherence heterodyne interferometry working with two wavelengths.

Typical parameters are roundness, straightness, parallelism, angle and diameter. The small optical probe allows fast non-contact measurements of very small and hard-to-access geometries, and provides optical contact at two different angles.

The first approach to the calculation of the measurement uncertainty of the generated 3D geometry data showed that the dimensional 3D standard measurement uncertainties only amounted to 7 nm for the piston and 15 nm for the cylinder.

This results in a relative measurement uncertainty for the cross-sectional area of 0.7 x 10-6, which may well contribute to decreasing the measurement uncertainty for the Boltzmann constant as a whole.

Mahr Federal Inc., a member of the Mahr Group, has been providing dimensional measurement solutions to fit customer application needs for over 150 years. The company manufactures and markets a wide variety of dimensional metrology equipment, from simple and easy-to-use handheld gages to technically advanced measurement systems for form, contour, surface finish and length. Mahr Federal is also well known as a producer of custom-designed gages and a provider of calibration and contract measurement services. Mahr Federal’s calibration laboratories are accredited to ISO/IEC 17025:2005 NVLAP Lab Code 200605-0 (see their Scope of Accreditation for accredited calibration processes).

For more information visit www.mahr.com.

For additional information, contact:

Marketing
Mahr Federal Inc.
1144 Eddy Street
Providence RI 02905 USA

Tel: (800) 343-2050 or +1 (401) 784-3100
Fax: +1 (401) 784-3246
Email: information@mahr.com
Web site: www.mahr.com


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

WordPress Anti Spam by WP-SpamShield